Jm 1325-20T Manuel d'utilisateur télécharger pdf (Page 16)

MAKE SURE THAT ALL POWER IS SHUT OFF AND THE UPPER AUGER TUBE IS IN THE DOWN

POSITION BEFORE REMOVING THE RESTRICTERS.

Remove restricters from 90 degree street elbow on hydraulic cylinder. Remove dirt from tting to allow

hydraulic oil to ow freely through the restricter. Reattach the restricter to the street elbow. Use teon

sealant tape or equivalent on the threads of the restricter before reattaching.

If restricter continues to plug with dirt, replace or lter the hydraulic oil in your system.

REMOVING DIRT FROM RESTRICTERS ON HYDRAULIC CYLINDER

REMOVING FROM STORAGE

Check the oil in the gearbox.

Check the battery and make sure that it is fully charged (if equipped with

an electronic weigh system). Reconnect the negative (-) cable.

Inate the tires to the correct operating pressures.

Close the clean-out door at the base of the grain tank.

Make sure that all shields are in the proper position.

Tighten the Slip Clutch Bolts until spring length is 1.27”.

STORAGE PREPARATION

IMPORTANT: When the grain cart is not going to be used for a length of time, store the cart in a dry, protected

place. Leaving your grain cart outside, open to the weather, will shorten its life.

Follow the procedure below when your grain cart is placed in storage for periods up to six months.

Cover electronic monitor (if equipped) with plastic before washing the grain cart. Wash or clean and

completely lubricate the grain cart. (*See the lubrication service section in this manual.)

Remove all grain from inside the grain tank, auger tube assemblies, and at the clean-out door.

Check gearbox oil in the gearbox and replace with new EP 80-90 gearbox lubricant if necessary.

Touch-up spots where paint has been worn away (use a good quality primer paint - especially before

applying graphite paint to the inside of the grain tank).

Retract all hydraulic cylinders to prevent the piston rods from rusting.

If the grain cart is equipped with an electronic weigh system, fully charge the battery to prevent freez-

ing. Disconnect the negative (-) ground cable at the battery to prevent possible discharge.

Clean the tires before storage. Inate the tires at regular intervals.

Open the clean-out door at the base of the grain tank.

Loosen the Slip Clutch Tension Bolts.

If the upper and lower ighting still does not separate properly during the folding sequence, a small bevel

may need to be ground out of the inside of the lugs where they meet the drive-dog. Grind approximately

1/8” off of the corner of the lugs where they touch against the drive-dog.

MAKE SURE THAT ALL POWER IS SHUT OFF BEFORE ADJUSTING THE FLIGHTING ASSEMBLY.

If the upper and lower ightings do not properly separate during the unfolding sequence, the upper ighting

may need adjusting. Before making adjustment to upper ighting, check to see if the lugs and drive-dog are

locking together by checking for a 1/8” space between the base of the 4-hole ange bearing and the upper

tube housing. (If not, dirt in the restricter or a faulty check valve on the hydraulic cylinder used to raise the

upper tube may be the cause of the problem. *See instruction for removing dirt from the restricter).

Fold the upper tube assembly into the upright position. Position upper ighting in engaged position with

lower ighting. Locate 4-hole ange bearing on top of the upper tube housing. With the upper ighting in

the engaged position, check the spacing between the upper bearing and the upper tube housing. There

must be a 1/8” space between the base of the 4-hole ange bearing and the upper tube housing. If there

is NOT a space between the bearing and the upper tube housing, or if there is more than a 1/8” space, the

upper ighting will need adjusting. To adjust the upper ighting, loosen the 1 1/4” hex nuts both below and

above the 4-hole ange bearing. Move the 1 1/4” hex nuts either up or down the threaded shaft on top of

the upper ighting until a 1/8” gap is between the base of the bearing and the upper tube housing. Tighten

the 1 1/4” hex nuts.

ADJUSTING THE UPPER FLIGHTING

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 32 33

Commentaires sur ces manuels

Pas de commentaire

Jm 1325-20T Manuel d'utilisateur Page 16

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel de jardinage Jm 1325-20T