Jm 1325-20T Manuel d'utilisateur télécharger pdf (Page 28)

SET-UP INSTRUCTIONS

Roll Tarps for Grain Carts

Center the lock panel from the front to the rear of

the cart on the off auger side of the cart. Make

sure that the lock panel is ush to the inside of the

sideboard. Holes may already be pre-drilled for the

installation or may need drilled out with a 1/4” drill

bit. Use a pair of vise grips to temporarily hold the

lock panel to the off auger side of the cart. Bolts

will be used in a later step that will secure the lock

panel.

Bolt together each of the end caps using 1/4”-20 x 1/2” hex

head bolts and 1/4”-20 serrated ange hex nuts. One end cap

will have a windlip sticking up and the other will be sticking

down. The endcap that has the 1” windlip sticking up is the

front endcap. On the front end cap leave the last four holes

empty on the opposite auger side. Use four 1/4”-20 x 5/8”

hex head bolts and four 1/4”-20 serrated ange hex nuts to

attach the plastic rail piece at the last four holes to the end-

cap assembly. The end cap that has the 1” lip in the opposite

direction of the rib is the rear end cap arch. This should be

paired up with the end cap plate that has three to four extra

holes in it (holes for the J-bolts) and is shorter.

Use four 1/4”-20 x 3/4” hex bolts, four 1/4”-20 centerlock

hex nuts, ve 3/8”-16 x 1” serrated ange hex bolts and ve

3/8”-16 serrated ange hex nuts to attach each of the end

caps. The end cap is pre-drilled, however, 1/4” holes may

need drilled through the top of the sideboards and 3/8” holes

may need drilled through the endboards to match the end-

caps hole pattern. Once this is completed, drill and install

one more 1/4”-20 x 5/8” hex head bolt at the end of the front

end cap through the plastic rail piece and a 1/4-20 x 1/2” at

the other end of the same end cap with no plastic rail piece.

1/4” x 1/2”

1/4” x 5/8”

Drilled and

installed

after end cap

is bolted to

Grain Cart.

Plastic Rail Piece

1/4” x 3/4”

3/8” x 1”

Install the two piece prop-up bars in the front and

rear of the Grain Cart. Install the Lower Portion of

the Bow Prop with one 3/8” x 1” Serrated Flange

Hex Bolt and one 3/8” Serrated Flange Hex Nut to

the rear brace rst (holes may not be pre-drilled for

this). Then, pushing up on the end cap, attach the

Top Portion of the Bow Prop to the Bottom Por-

tion of the Bow Prop with two 3/8” x 1” Serrated

Flange Hex Bolt and two 3/8” Serrated Flange Hex

Nut so that the Two Piece Prop-Up Bar is pushing

the end cap upwards to keep from sagging.

Two Piece Bow

Prop holding up

the end cap.

Top Portion of

the Bow Prop

Lower Portion of

the Bow Prop

Installing the Lock Panel (Drip Edge)

Installing End Caps and Plastic Rail

Installing Bow Prop on Endcaps

Lock panel placed

on Opposite

Auger Side.

1 2 ... 23 24 25 26 27 28 29 30 31 32 33

Commentaires sur ces manuels

Pas de commentaire

Jm 1325-20T Manuel d'utilisateur Page 28

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel de jardinage Jm 1325-20T